Crimping tools offered by ERKO assortment guarantee durable and reliable connections. The connection is obtained by means of properly selected hand, hydraulic or pneumatic tools. For crimping terminals and connectors with small diameters manufacturer recommends manual presses or pneumatic stationary solutions. For larger ranges of terminals and connectors it is recommended to use hydraulic tools equipped with clamping dies.
Manual, mechanical presses offered by the assortment ERKO are designed for different types of terminals, equipped with two or three terminal sockets and ratcheting mechanism. Manual presses T type eg .: T 22- 6 are designed for crimping cable end-sleeves in the range of 0.5 to 6 mm2, presses A type eg .: A 11-6 are used for ring cable connectors (KOA), spade (KNA), pin (KWA) and tubular connectors without insulation (type KLA) in the range of 0.5 to 6 mm2, manual hand presses E type used for terminals and connectors with insulation: ring (KOE, KOV), spade (CIE, KNV), pin (type KWE, KWV) in the range of 0.5 to 6 mm2. The manufacturer has in its offer also presses for crimping the receptacles, tabs and claw terminals. Among the hand crimpingtools, manufactured by ERKO, is manual hand crimping tool PR 33 which is very popular.
The distinctive feature of the tool is easily interchangeable crimping dies. The manufacturer offers a range of crimping dies most frequently used during installation and electrical work. Dies were selected for ring insulated and non-insulated terminals, cable end-sleeves and receptables. The scope of crimped terminals and connectors is set in the range of 0.5 to 6 mm2 and cable end-sleeves from 0.5 to 35 mm 2 replaceable crimping dies are mounted in prasce by a spring catch. This solution does not require any devices to exchange matrices, which significantly affect the functionality of the tool. Assembly of the product is carried out using an automated line. This allows for parameters directly affecting the durability and reliability of the press. The use of two component non-slip handle in the press provides a comfortable, safe operation and ergonomic sure grip. When designing the press the individual needs of the Client were taken into account, proposing any crimping dies completion. For the manual crimping tool line should also be a mechanical press T10-seated designed for pressing in the form of a square wire end connectors with insulation veins of copper cables having a cross section stranded 0.5 to 10 mm2.
When designing the press individual needs of the Client were taken into account, proposing any crimping dies completion. To the manual crimping tool should also be a mechanical press T10-seated designed for pressing in the form of a square cable end-sleeves with insulation on copper cables having a cross section from 0.5 to 10 mm2. Two-component handle, ensures longer tool life, and ergonomic design, eases the use and improves the efficiency of work.
Manual hand press type PR 50, PR 120, PR 150 and PR 95A, depending on the nature of the crimping dies enable crimping of tubular aluminum connectors in the cross section of 16-95 mm2 (PR 95A) or copper (PR50 in the cross section of 6-50 mm2, PR 120 cross section of 10-120 mm2, PR 150 in the range of 25-150 mm 2). Rotary crimping dies fitting allows fast operation (no need to replace die if we need to crimp various cross sections of the terminals). Feature stamped on the crimping die indicates the cross-section of Al and Cu cables. Crimping the connector tip in the form of a hexagon provides a permanent connection. Slightly larger diameters terminals and connectors you can crimp with the press PRZ 240 and PR 240. Using the appropriate crimping die allows to crimp cable end- sleeves (range 10-120 mm2), insulated cable connectors or without insulation (10-120 mm2) and the tubular and aluminum (16 -240 mm 2 and copper 6-240 mm 2). Presses and hydraulic heads are widely used, so the company ERKO created a wide range of such products. Among them are tools for an average intensive work, such as model HRZ 300 with a snap swivel head 180 ° and a pressure of up to 66.6 kN, and hydraulic crimping tool HR 300. For intensive work ERKO recommends hydraulic heads cooperating with hydraulic units H 800 also with units AH 500 and AH 550. GU 300 hydraulic head additionally allows you to cut holes in the bednarce, and the head GU 625 allows crimping terminals and connectors with cross section up to 625 mm2.
Electric crimping presses EPZ 300 and EPZC 300 type were designed on the basis of the rotating head. EPZC model stands out with its snap pivoting head rotating at an angle of 360 ° and an extremely powerful lithium-ion battery. Additionally electric crimping press has a switch circuit breaker ending work cycle after the proper crimping has been done and is equipped with LED diode to signal normal or abnormal crimping. A big facilitation is electronic registration of the work cycle and automatic pressure control.
Elektrical press EPZ 300 type is characterized by extremely short crimping time of crimping the connectors (3-6 seconds) and the battery capacity of up to 250 crimps without charge. The great advantage of this model of electrical press , is the ability to precisely monitor the work. Electronically controls and registers the correctness of the cycle. It includes installation CD which allows to read information about the correctness of crimping and amount of cycles completed. In addition, the siren installed, will inform us about the required periodic review and indicate battery charge status. In addition to mechanical and hydraulic crimping tools ERKO company also offers pneumatic tools for crimping and cutting cables. Pneumatic presses supplied by compressed air cooperate with the heads crimping terminals on the wires with cross sections from 0.5 to 50 mm2 and for cutting cables. Thanks to the use of PPH 13, it is possible to cut copper wires, stranded insulated with a thickness of 25 mm2. It can optionally be equipped with a crimping control system SP 1. It is characterized by a maximum efficiency of 50 cycles per minute.